Cover Junior ADU Conversion: The Henderson Owner’s Guide
The Cover junior ADU conversion (the interface and tie-in work that connects a Cover Jr. unit to your existing home, its slab, and your utilities) typically runs $8,500 to $19,500 installed in Henderson, depending on which model you have, whether the site is already prepped, and how much electrical and plumbing has to be reconciled at the connection point. Most owners don’t go looking for this part. They find it when the unit stops feeling like part of the house: a soft spot at the threshold, a door that won’t latch flush, water tracking along the base where the conversion meets the original wall, or a suddenly tripping breaker on the feed to the unit. Those are the usual first symptoms. Call (855) 953-5331 and a live person answers, day or night, to start a free estimate.
Which Cover Models This Applies To

Cover has built more than one generation of its junior line, and the conversion hardware is not interchangeable between them. The earliest Jr. units and the later refreshed models use different threshold profiles, different anchor spacing at the sill, and different electrical feed routing. Before we quote anything, we confirm your exact model by the data plate on the unit (usually inside the access panel or near the entry frame), the serial on your delivery paperwork, and physical measurements at the threshold and the wall penetration. That last step matters most: a conversion kit that fits the model on paper can still miss by a fraction on a site where the slab was poured slightly out of level.
On the OEM-versus-aftermarket question, our honest position for Cover specifically: the model-specific conversion components are worth sourcing genuine when they’re still available, because the fit tolerances at the sill and the wall tie-in are tight. For the generic parts around them (fasteners, flashing, weather seal, trim), a quality aftermarket equivalent is fine and often better suited to Henderson’s heat. We’ll tell you which is which in writing before you approve anything. Fielding ADU Builders Henderson is an independent service provider and is not affiliated with Cover.
Signs Your Cover Junior ADU Conversion Is Failing
- Water at the threshold after rain. The sill seal or flashing detail has opened up, and in Henderson’s monsoon season (July through September) that shows as damp flooring or staining at the door base within hours of a storm.
- A door that drags, sticks, or won’t latch. Usually the anchor or shim package has settled, or the slab-to-unit connection has shifted with the seasonal soil movement we see across the valley’s expansive clay soils.
- Sun-baked sealant pulling away from the seam. Henderson summers routinely push past 110°F, and the sealant at the conversion joint cooks, cracks, and loses adhesion faster here than the manufacturer’s lifespan figure assumes.
- Breaker tripping or flickering on the unit’s feed. The electrical penetration or the junction at the conversion point has moisture intrusion or a loose connection, and it needs a licensed electrician, not a reseat-and-hope.
- Visible gap or daylight at the wall tie-in. The structural connection between unit and house has loosened or was never fully fastened, and this one should be looked at before the next wind event, not after.
Replacement Cost & What’s Included

Installed pricing in Henderson breaks down roughly like this:
| Scope | Typical installed range |
|---|---|
| Seal and flashing renewal only (no structural work) | $850 – $2,400 |
| Threshold and sill package replacement (model-matched) | $2,200 – $5,800 |
| Full conversion tie-in rebuild, unit-to-house, including electrical and plumbing reconciliation | $8,500 – $19,500 |
| Electrical or plumbing correction at the connection point (licensed trade, permitted) | Quoted line-item, typically $1,200 – $4,500 |
What moves you up or down the range: model generation, condition of the slab, whether the original install left the connection accessible, and how much of the utility work is compliant versus needs correcting. You get the price in writing before any work starts, so the number you approve on day one is the number on the final invoice. The work is covered by the Garrison Standard: workmanship defects for 365 days, and if something fails inside that year, we come back and make it right at no charge.
DIY or Call Us?
Here’s the honest split. You can safely check the surface: look for daylight at the seam, run a hose test at the threshold for a few minutes, photograph any staining, and confirm your unit’s model and serial from the data plate. That information helps us quote accurately and costs you nothing.
Where DIY goes wrong on this part is the structural and electrical side. The tie-in carries load between the unit and your house, and a re-anchor done at the wrong spacing or torque can loosen the connection it was meant to fix. The electrical feed at the penetration is real line voltage, and Henderson permitting expects that work to be done by a licensed electrician and inspected. We’re background-checked, uniformed, and permitted by the book, and our technicians have up to 20 years of experience with prefab and modular platforms. Call (855) 953-5331 for a free estimate before you pick up a tool.
FAQs

How long does a Cover junior ADU conversion last in Henderson? Expect the seal and flashing to need attention every 5 to 8 years in Henderson, not the 10 to 12 years a milder climate might give you, because the UV load and 110°F-plus summers age the joint faster. The structural tie-in itself should outlast that if it was installed correctly to begin with.
Can the conversion be repaired instead of replaced? Often, yes. If the failure is confined to sealant, flashing, or the threshold package, a targeted repair is the right call and costs far less than a full rebuild. If the anchor package or the structural tie-in has failed, a repair is just delaying a replacement. We’ll tell you which one you’re looking at, in writing, before you approve.
How long does the swap take? Seal and flashing renewal is usually a single day. A threshold and sill replacement runs one to two days. A full conversion tie-in rebuild typically takes three to five working days once the model-matched parts are on site and any permit is pulled. We confirm the schedule in the written quote, and someone answers the phone 24 hours a day if the plan changes.
How do you source the part? We identify your Cover model from the data plate and measurements, source the genuine model-specific components when they’re available, and use quality aftermarket equivalents for the generic hardware where it makes sense. We don’t carry stock and won’t tell you a part is “on the truck” – we confirm the source and lead time in your written price. Fielding ADU Builders Henderson also works the other major brands, including Abodu and Dvele, so we’ve seen how these connections hold up across the platforms. Call (855) 953-5331 to get started.
Whether you’ve got a soft spot at the threshold, a door that won’t latch, or just a nagging doubt about the connection on your Cover Jr., the next step is a free estimate. Call Fielding ADU Builders Henderson at (855) 953-5331 and a live person will pick up, day or night. We’ll confirm your model, put the price in writing before any work starts, pull the permits, and stand behind the work for a full year under the Garrison Standard.
Written by the team at Fielding ADU Builders Henderson, serving Henderson and nearby areas.











